Pan-tilt Bracket for Servo SG90S MG90S
: Vous pouvez voir les tarifs d'expédition et estimations de livraison cliquant ici
: Retour sous 7 jours avec conditions, cliquez pour plus de détails
Description
FPV pan tilt aerial photography pan tilt support special pan tilt for aerial model, double axis servo pan tilt image transmission partner

Note: the pictures show the complete installation effect. The steering gear and camera need to be purchased separately. They are available in our store. This pan tilt is in bulk and can only be assembled with steering gear and camera. You can contact our store for installation help videos.

With SG90 type steering gear, plastic gear 9g servo:
The rocker arm of the steering gear needs to be cut off a little before installation, and the installation of the steering gear on the base also needs to modify the rocker arm (remove the edge of the round hole, and then put the rocker arm in or trim the steering gear arm)!
At present, this kind of PTZ can only be installed with 28*28 camera modules, not 32 or 38 size cameras. (please know that the rudder arm of the steering gear needs to be trimmed.)


The 2-axis plastic pan tilt weighs 17 grams, which is suitable for 9g-12g steering gear. It has beautiful appearance, precise manufacture, no virtual position and no shaking. It has a steering gear wire winding clamp.
The product is shown in the figure, 4 nylon plastic parts, including screws. Self assembly is required.



Product parameters
Applicable servo model: SG90
Product weight: 17g
Working torque: 1.8kg/cm (4.8V)
Reaction speed: 0.1sec/60degree (4.8V)
Rotation angle: 90 degrees
Working voltage: 4.8V
Working temperature: 0 ℃ - 55 ℃
Dead band setting: 10us
Gears: Plastic Gears
Pin definition: Orange signal
red VCC
Brown GND


Installation demonstration


Avis clients
Aucun avis publié pour le moment.
Connectez-vous pour ajouter votre avis.
Description & retour
Product parameters
Applicable servo model: SG90
Product weight: 17g
Working torque: 1.8kg/cm (4.8V)
Reaction speed: 0.1sec/60degree (4.8V)
Rotation angle: 90 degrees
Working voltage: 4.8V
Working temperature: 0 ℃ - 55 ℃
Dead band setting: 10us
Gears: Plastic Gears
Description
FPV pan tilt aerial photography pan tilt support special pan tilt for aerial model, double axis servo pan tilt image transmission partner

Note: the pictures show the complete installation effect. The steering gear and camera need to be purchased separately. They are available in our store. This pan tilt is in bulk and can only be assembled with steering gear and camera. You can contact our store for installation help videos.

With SG90 type steering gear, plastic gear 9g servo:
The rocker arm of the steering gear needs to be cut off a little before installation, and the installation of the steering gear on the base also needs to modify the rocker arm (remove the edge of the round hole, and then put the rocker arm in or trim the steering gear arm)!
At present, this kind of PTZ can only be installed with 28*28 camera modules, not 32 or 38 size cameras. (please know that the rudder arm of the steering gear needs to be trimmed.)


The 2-axis plastic pan tilt weighs 17 grams, which is suitable for 9g-12g steering gear. It has beautiful appearance, precise manufacture, no virtual position and no shaking. It has a steering gear wire winding clamp.
The product is shown in the figure, 4 nylon plastic parts, including screws. Self assembly is required.



Product parameters
Applicable servo model: SG90
Product weight: 17g
Working torque: 1.8kg/cm (4.8V)
Reaction speed: 0.1sec/60degree (4.8V)
Rotation angle: 90 degrees
Working voltage: 4.8V
Working temperature: 0 ℃ - 55 ℃
Dead band setting: 10us
Gears: Plastic Gears
Pin definition: Orange signal
red VCC
Brown GND


Installation demonstration


Politique de retour Websoog
Si vous n'êtes pas satisfait d'un produit acheté sur websoog.com, ou si celui-ci est défectueux ou endommagé, vous pouvez le retourner dans les 8 jours suivant la date de livraison, et nous procéderons à son remplacement. Veuillez noter que si la commande dépasse ce délai, nous ne pourrons pas accepter le retour. Les produits sont échangés uniquement, aucun remboursement n'est effectué.
Échange possible si le produit ne correspond pas à l'image ou à la description.
Nous traitons les anomalies, défauts, produits endommagés ou pièces manquantes.
Une vidéo complète permet de protéger vos droits et d'accélérer le traitement.
Conditions pour échanger un produit
- Si le produit ne correspond pas à l'image présentée sur le site.
- Si le produit présente un défaut ou une anomalie.
- Si le produit est endommagé.
- Si le produit est une contrefaçon.
- Si le produit manque certaines de ses pièces.
- Si vous n'êtes pas satisfait du produit, sans que les raisons mentionnées ci-dessus soient en cause, les frais de retour seront à votre charge.
Conditions vidéo pour garantir votre droit de retour et d'échange
Pour protéger vos droits et éviter tout malentendu, merci de respecter les étapes suivantes :
- Filmez le colis avant ouverture pour montrer l’état de l’emballage extérieur.
- Assurez-vous que l’étiquette avec votre nom et adresse soit bien visible dans la vidéo.
- Enregistrez l’intégralité de l’ouverture du colis, sans interruption, jusqu’à ce que le produit soit entièrement sorti.
- Une fois le produit sorti, filmez-le sous tous les angles.
- Si le produit est électronique, montrez son fonctionnement et ses fonctionnalités principales dans la vidéo.
- Si des défauts, anomalies ou pièces manquantes sont constatés, filmez-les clairement.
Méthodes pour échanger un produit
Lors de la réception du nouveau produit, vous devrez payer un montant spécifique en garantie. Remettez l'ancien produit au bureau de livraison au moment où vous recevez le nouveau produit. Une fois le produit retourné reçu, nous inspecterons son état. Si le produit est en bon état, le montant de la garantie sera restitué. Si le produit est en mauvais état, une déduction sera effectuée sur la garantie, en fonction de l’état du produit.
Vous envoyez le produit pour inspection. Après vérification de son état, un produit de remplacement vous sera envoyé. Cette méthode prend plus de temps.
Produits non éligibles à l'échange
- Produits ouverts qui ne peuvent pas être retournés pour des raisons d'hygiène ou de santé.
- Enregistrements audio/vidéo ou logiciels ouverts après livraison.
- Produits personnalisés ou fabriqués sur commande.
- Produits susceptibles de se détériorer rapidement.
- Contenu numérique non fourni sur support matériel (CD, DVD, etc.).
- Produits volumineux nécessitant un montage, comme les meubles.
Connectez-vous à votre compte via le lien suivant : Connexion à votre compte. Remplissez ensuite le formulaire de demande de retour en y ajoutant la vidéo comme preuve.
Product parameters
Applicable servo model: SG90
Product weight: 17g
Working torque: 1.8kg/cm (4.8V)
Reaction speed: 0.1sec/60degree (4.8V)
Rotation angle: 90 degrees
Working voltage: 4.8V
Working temperature: 0 ℃ - 55 ℃
Dead band setting: 10us
Gears: Plastic Gears
Description
FPV pan tilt aerial photography pan tilt support special pan tilt for aerial model, double axis servo pan tilt image transmission partner

Note: the pictures show the complete installation effect. The steering gear and camera need to be purchased separately. They are available in our store. This pan tilt is in bulk and can only be assembled with steering gear and camera. You can contact our store for installation help videos.

With SG90 type steering gear, plastic gear 9g servo:
The rocker arm of the steering gear needs to be cut off a little before installation, and the installation of the steering gear on the base also needs to modify the rocker arm (remove the edge of the round hole, and then put the rocker arm in or trim the steering gear arm)!
At present, this kind of PTZ can only be installed with 28*28 camera modules, not 32 or 38 size cameras. (please know that the rudder arm of the steering gear needs to be trimmed.)


The 2-axis plastic pan tilt weighs 17 grams, which is suitable for 9g-12g steering gear. It has beautiful appearance, precise manufacture, no virtual position and no shaking. It has a steering gear wire winding clamp.
The product is shown in the figure, 4 nylon plastic parts, including screws. Self assembly is required.



Product parameters
Applicable servo model: SG90
Product weight: 17g
Working torque: 1.8kg/cm (4.8V)
Reaction speed: 0.1sec/60degree (4.8V)
Rotation angle: 90 degrees
Working voltage: 4.8V
Working temperature: 0 ℃ - 55 ℃
Dead band setting: 10us
Gears: Plastic Gears
Pin definition: Orange signal
red VCC
Brown GND


Installation demonstration















